Witura WT9002 Manual de usuario descargar pdf

1|Page

User Manual V2.6 Date: 12/6/2012

Installation of the Interface and Call point

The Interface is housed in a back flanged IP65 Rated Enclosure and can be located and fixed

without having to open the cover or requiring any internal fixings within the enclosure making it

a secure and waterproof Installation giving maximum protection for the control equipment inside.

The Call Point is a two piece fixing with the shield located and fixed and the main Intercom fascia

locked into place and secured via the security fixing on the under frame of the casing and again

providing a very secure vandal resistant and waterproof housing.

The New GSM Intercom WT-9002 has been designed as a system to communicate via a fixed call

Point to either a land line or Mobile using the GSM Network without the requirement of any

cabling from the gate entry to the point of contact and also eliminating the problems that occur

with long range wireless systems as this system has no range barriers as long as an acceptable

GSM-Network is available at the site location.

This system also allows the person called to operate two separate relays using the key pads on

either the Land Line or Mobile Phone regardless of the location or distance apart and these may

represent a gate and a door or entrance lights etc

Other features include a Battery Backup to alert you when the mains power fails at the gate and

the system can also sound an audible alarm in the event the power fails to further alert the

property owner.

Introduction

The system comes with a complete GSM Interface in an IP 65 Enclosure and a Stainless Steel

external Call-Point requiring only a 6 wires connection between the Interface and the Call Point.

The system also has the facility to store up to 1000 authorized users who can access the system

via Mobile phone or Landline and these numbers can be programmed via text messaging or using

the software package provided with the system.

It is also possible to change or override the parameters of both the output relays remotely via

SMS and receive confirmations of these commands and add and remove authorized users without

having to be present on site or again use the software package provided with the system.

GSM Intercom Remote Control and Alarm System

Product Model: WT9002

–

V2.0 2012

1 2 3 4 5 6 ... 19 20

Indice de contenidos

Pagina 1 - V2.0 2012

1|Page User Manual V2.6 Date: 12/6/2012 Installation of the Interface and Call point The Interface is housed

Pagina 2

10|Page User Manual V2.6 Date: 12/6/2012Permanently Latching both Relays It is possible also to permanently Latch both Relays either on or off in

Pagina 3 - Hardware Description:

11|Page User Manual V2.6 Date: 12/6/2012To check the SMS messaging matrix setting you would send the following SMS Message to the system. Message

Pagina 4

12|Page User Manual V2.6 Date: 12/6/2012Description: A stands for the possible action (Selectable) 0 - 4 M1 stands for enable (1) / disable (0) sen

Pagina 5

13|Page User Manual V2.6 Date: 12/6/2012Input Alarm Message Settings It is possible to change the Input Alarm display message for both Alarm Input

Pagina 6

14|Page User Manual V2.6 Date: 12/6/2012STO2<Gate2 Closed!> and the input 1 restoral message has been programmed successfully Input Trigger

Pagina 7

15|Page User Manual V2.6 Date: 12/6/2012Power down Siren Output The system also has a Siren output which is activated also when the power supply

Pagina 8

16|Page User Manual V2.6 Date: 12/6/2012Message received ALM1:ON/OFF ALM2:ON/OFF ALAC:ON/OFF ALTM:<00600> or similar Check the Signal Str

Pagina 9

17|Page User Manual V2.6 Date: 12/6/2012Learning Mode for Remote Controls It is possible to add remote controls for the system to do so you must h

Pagina 10

18|Page User Manual V2.6 Date: 12/6/2012List of S.M.S Commands * * *TEL1#ReturnMessageTEL1=<

Pagina 11 - Setting the Alarm Inputs

19|Page User Manual V2.6 Date: 12/6/2012 *ALAC#ALAC‐ON01*ALAC#TurnPowerdownTextAlertsOff*ALTM#*ALNF#

Pagina 12

2|Page User Manual V2.6 Date: 12/6/2012It is advised the distance from the Interface to the Call Point des not exceed 3 meters and it is also advis

Pagina 13

20|Page User Manual V2.6 Date: 12/6/2012Specifications  Dual Band (900/1800Mhz) or Quad Band Module (850/900/1800/1900Mhz)  Power Supply: 15

Pagina 14 - Power down Alarm

3|Page User Manual V2.6 Date: 12/6/2012Hardware Description: Wiring Diagram:

Pagina 15

4|Page User Manual V2.6 Date: 12/6/2012 To Install the SIM Card you will need to lift up the card carrier and slot in the SIM Card and locate it i

Pagina 16

5|Page User Manual V2.6 Date: 12/6/2012same number in both admin 1 and admin 2 slot or even admin 3 can all be the same number of which the system

Pagina 17 - Reset the System

6|Page User Manual V2.6 Date: 12/6/2012To enable the function mode to be able to store the Guest List Numbers you would send the following SMS Mess

Pagina 18 - List of S.M.S Commands

7|Page User Manual V2.6 Date: 12/6/2012Setting up the Intercom parameters The system allows you to adjust certain parameters such as ring time, s

Pagina 19

8|Page User Manual V2.6 Date: 12/6/2012Adjusting Speaker Volume It is possible to adjust the Microphone Volume via SMS Message from a 0 setting u

Pagina 20 - Specifications

9|Page User Manual V2.6 Date: 12/6/2012 Message Sent *EXT2#00360 The visual screen will light up when this message has been received and if is in

Mas documentos para Controles remotos Witura WT9002

a Ver el documento Witura WT9002 Manual de usuario

Witura WT9002 Manual de usuario (47 paginas)

Comentarios a estos manuales

Sin comentarios

Witura WT9002 Manual de usuario

Busca en linea o descarga Manual de usuario para Controles remotos Witura WT9002. Witura WT9002 User manual Manual de usuario

Indice de contenidos

Mas documentos para Controles remotos Witura WT9002

Comentarios a estos manuales